In many cases, replacing the drain hose of a washing machine requires access to its body.
As a rule, the drain hose is made of corrugated, i.e. it is corrugated, and is reinforced in the middle of the washing machine near the drain pump.
After that, it is located along the walls of the body of the washing device and is brought out through the back panel, sometimes from below, sometimes from above.
Content
- How to get to the drain hose
- Changing the drain hose in an AEG, Bosch and Siemens washing machine
- Changing the drain hose in Ariston, Indesit, Samsung, Ardo, BEKO, LG, Candy and Whirpool washing machines
- Replacing the drain hose of Elestrolux and Zanussi washing machines
- Replacing the drain hose on top-loading machines
How to get to the drain hose
That is why, to replace the hose, washing machines need to disconnect the hose from drain pump, and after and from the very body of your washing unit.
In order to make it more convenient for you, you can detach the top hatch of the washing machine.
Let's look at several options for accessing the connection drain hose, based on the individual characteristics of each design from various groups and subgroups.
Changing the drain hose in an AEG, Bosch and Siemens washing machine
In these cases, you can get an inlet to the drain hose fixture for washing units of this group through the front panel.
How to remove the front panel
Loosen the clamp and carefully disconnect manhole cuff from the front panel of the washing machine.- Remove the dispenser.
- Detach the decorative panel at the very bottom.
- Pour the remaining water through pump filter elementby placing a rag under it.
- Unscrew the screws securing the front panel to the device case. One bolt will be at the top and 2 at the bottom.
- Take the lower part of the panel slightly towards you, then move it down and disconnect the entire panel by about 5-8 cm.
- Disconnect and cords from blocking holes that are on the wall.
How to remove and install the drain hose
When you have finally gained access to the interior of your washing machine, remove the clamp drain hose and disconnect the hose from the drain structure.- Insert the new hose tightly in place of the old part, and clamp it all with a clamp.
- Next, we run the hose along the walls, attach it to the shell of the device and bring it out.
- Connect the end of the hose (outlet) to the sewer and check your installed part for tight connections.
Changing the drain hose in Ariston, Indesit, Samsung, Ardo, BEKO, LG, Candy and Whirpool washing machines
In washing units of this group, access to the hose, or rather its attachment, can be found through the bottom of the structure.
Disconnect the bottommost panel that seals the pump filter.- Pour out the remaining water, while unscrewing with the greatest care filter.
- Pull the washing machine forward, and when you tilt it back, place it against the wall.
- Starting work at the bottom of the device, unscrew all the screws securing the “snail”, remove it from the case and lower it.
When you get access to the drain hose, disconnect it from the drain system, after loosening the clamp with round-nose pliers.- Try to remember the location of your old drain hose in the middle of the body, and then disconnect it and remove it. For convenience in this type of dismantling, we recommend removing the outer cover of the structure.
- Connect the newly purchased hose and assemble the washing machine in reverse order.
- Connect the hose to the sewer and check the tightness of the drain hose connections on both sides.
Replacing the drain hose of Elestrolux and Zanussi washing machines
In the washing designs of Electrolux and Zanussi, access to the elements inside is carried out by opening the back wall of the panel, since the bottom is almost impossible to open, and the front panel does not open at all.
How to remove the back cover
Remove the outer cover of the washing machine. To do this, unscrew the 2 fastening screws from the rear panel, move the cover back and disconnect it.- Next, you should begin to unscrew the screws on top and a couple on the sides (they can be found under the plugs), and two or three from the bottom.
- We separate the plastic fastenings of the intake valve from the rear panel and carefully disconnect the back wall.
How to remove and install the drain hose
After dismantling the rear panel, we got access to all the elements. Now you need to drain the remaining water through the drain hose. To do this, lower it as low as possible and substitute some kind of cup and rag for safety in advance.- Next, we look for the fastening of our hose and disconnect it by loosening the clamp.
- We disconnect the hose from the body, after remembering the location.
- We attach a new part in place of the old one, and fix it with a clamp.
- We connect the free end to the sewer and check the level of tightness.
- We assemble the back panel in descending order of all the above steps.
Replacing the drain hose top loading washing machine
In order to access the replacement of the drain hose in vertical type washing machines, it is enough just to remove the side cover.
In order to remove the side wall, unscrew the screws from the end on the back of the case, unscrew one screw from the end, front and from the bottom panel. Next, slide the side wall off the rear panel, lower it down and detach.- After gaining access to the hose mount, loosen the clamp and remove it.
- Dismantle the hose from the housing and stick it out of the washing machine.
- Install the hose in reverse order.
