The following may happen with the Samsung washing machine: some time after the start of washing, you find that you do not hear the water entering the tank and pay attention that one of the error code options 1C, 1E is lit on the electronic display, and on models produced before 2007 E7 . Perhaps the error was displayed during the previous wash at the time of spinning or rinsing, but at that moment you did not pay attention to it. But after 10-20 seconds of a new cycle, it repeated itself and stopped the washing machines.
If there is no scoreboard on the control panel, then you will determine this error by the burning indicator lights for washing in hot water and the temperature indicators of 60, 40 degrees, while the rest of the indicators are flashing.
Explanation of errors
In the device of a Samsung household appliance, there is such a part as a pressure switch. In other words, it is a water level sensor. In the event of a failure, the sensor produces a frequency that does not correspond to the washing cycle, the water is drained and an error 1E, 1C, E7 is displayed on the display. Most often this means a breakdown of the pressure switch, but at first it is recommended to try to solve the problem yourself.
What to do if error code 1E appears on the Samsung washing machine monitor:
It is possible that you will be able to fix this breakdown without calling the wizard. To do this, do the following:
- Checking the control module.
Turn off the device from the network and turn it on no earlier than after 5 minutes. Rebooting the controller will most likely restore the washing machine to working order.
- Checking the contacts at the pressure switch and the control board.
It is possible that one of the connectors has come off on the control module board or the pressure switch. It is necessary to review all contacts and correct, if possible.
- Checking the pressure switch tube.
It is necessary to see if the sensor tube that connects it to the pressure sampling chamber has disconnected, or if a kink has formed on it. It serves to ensure that at the time of filling the tank, the pressure selection is activated and the water stops flowing. In the event of a kink or disconnection, an error 1E (E7.1C) will be displayed. This is easy to fix on your own.
Calling a Professional
The table below lists the troubleshooting options for this error. master by repair or replacement of spare parts, as well as the cost of these works:
| signs the appearance of an error |
Possible cause of the error | Necessary actions
|
Repair cost, including spare parts, rub |
| There is no water entering the tank of the washing machine, the display code is 1E, 1C or E7. The first error signal can be received at any time during the washing process. | The most common failure is the failure of the pressure switch for one of the reasons:
|
Replacing the pressure switch or repairing the pressure level sensor hose in one of the following ways:
|
1500-3800 |
| The monitor shows an error 1E, 1C when starting the washing machine | Failure of the control module due to problems with the processor in the chip. Perhaps the resistors have burned out and there is no contact between the control board and the pressure switch. | Soldering resistors on the control module
or replacement of the control module in case of processor failure |
3900-5600 repair
7100 replacement |
| In the first minute of operation, the display issues the code E7.1E. A washing machine without a display gives an error with a combination of indicators (see above) | The wiring in the section from the pressure switch to the control module does not work, probably damage or oxidation of the contacts. | Cleaning contacts at the water level sensor, replacing internal wiring if twisting is ineffective | 1600-3000 |
**All repairs are typically covered by a two-year warranty.
You can leave an online application to the master around the clock. In it, you can briefly describe your problem, be sure to indicate the model of your washing machine, and leave contacts for feedback.
The specialist will arrive at the time you choose from 9.00 to 21.00, diagnose your household appliance, calculate the cost of repairs taking into account your Samsung washing machine model and perform all the necessary work to eliminate the 1E (1C, E7) error. If you are not satisfied with the price, you can refuse to repair, in this case you are not obliged to pay for the repair of a specialist, only $ 400-5 lei for diagnosing the problem
