Determining the meaning of errors washing machines Atlant: Overview

Atlant - a domestic washing machine that has a self-diagnosis unit. There are two types of models of this brand: with a display and with LEDs. Atlant washing machine error codes with a display are alphanumeric. On washing machines without a display, errors are displayed on the indicator light. Fault codes are decrypted by the user on their own, which will help to identify and fix the breakdown.

Let's analyze the error codes of these both generations of Atlant washing machines.

General information

Indicator values ​​for SoftControl and OptimaControl models

Important! The first indicator situated on right

Errors on washing machines Atlant. Full review

Below are the errors on all Atlant washing machines. In parentheses are the indicator values ​​for washing machines without a display. What do the errors mean and how to fix them? Consider below.

Sel (all indicators not are burning)

The error is in the malfunction of the program selector, that is, it simply does not work. Perhaps the potentiometer that selects the programs has broken. The reason may be, both in mechanical breakdowns, and in electronics.

Problem fix:

The buttons need to be cleaned. They could get dirty from frequent use and start to stick. Check if the buttons are loose. Perhaps some of them loosened up and stopped responding to pressing.Faulty ones will need to be replaced. The selector may be broken. We check its correctness. It may need to be repaired or replaced with a new one. If the selector is OK, but the problem is in the controllers connected to it. We check them and replace the faulty ones.

None (glow all indicators)

The reason is excessively formed foam in the drum. This can happen if the wrong powder is used (hand washing powder is not recommended in the washing machine) or too much was added. In addition, the problem is poor water drainage or the level sensor is broken. You could also set the wrong washing mode.

Problem fix:

Unplug the washing machine, take out the clothes and dispose of foam. Adjust the mode. Next time, use a different detergent or reduce the amount. If after these steps the error does not disappear, then the problem is with the water or foam level sensors. Ring the circuit and sensors. Replace them if necessary.

F2 (lit third indicator)

The error appeared due to a temperature sensor failure. It could break, contacts could come off, or something was wrong with the wiring. In addition, the control module could also break.

F2 error fix:

Check contacts and all wires. Ring the chain. It may be necessary to repair the wiring or tighten the contacts.

Check sensor. It may need to be replaced.

Check the control module. If it is defective, replace.

F3 (lit third and fourth indicators)

Error F3 of the Atlant washing machine appeared due to poor water heating. Most likely the error appeared due to a problem with the heating element (heating element), broken contacts, part of the wiring or breakage of the control module.

F3 error fix:

Check the voltage at the socket. If the voltage is too low, then this is the cause of the F3 error.

Check wiring. If its malfunction between the heating element, the controller and the temperature sensor can be corrected, do it.

Check contacts. They must be securely fastened.

Perhaps there is no signal from the temperature sensor. Replace it.

Check TEN. The problem is in the relay or a large layer of scale. The problem with the heating element can only be solved by replacement.

F4 (glows second indicator)

Error F4 occurs when there is a problem with draining water from the washing machine. This means that the drain pump is broken, the drain hose is clogged, the hose is not installed correctly, a foreign object has got into the pump, the drain coupling is clogged or broken.

F4 error fix:

• Check drain hose for kinks or blockages.
• Make sure the hose is installed correctly.
• Examine the pump. If there is debris in it, remove it. If it is broken, then replace it.
• Examine the drain plug. It has a ball that could fall. You will have to drain the water manually and replace the clutch. If it has a blockage, remove it.
• Inspect contacts and wiring. Troubleshoot.
• If the problem persists, then the error is due to the electronics module. It will have to be replaced.

F5 (glow second and fourth indicators)

The error occurred due to insufficient filling of the tank with water. Therefore, there is a problem with the fill valve, filters, fill hose or plumbing system.

Solution:

Check if there is water in the pipes, if all taps are open. Check the inlet hose. Remove this hose from the washing machine. Clean and run water. Clean the filter at the inlet hose. Examine the filling valve. It may need to be replaced.Inspect the contacts and all wires of the control module and fill valve. If these steps did not fix the error, then you will have to change the control module.

F6 (glow second and third indicators)

Most likely the error arose because there is a problem in the motor of the washing machine. The winding has overheated or the motor thermal protection contacts have become disconnected.

Solution to F6 problem:

• Check all contacts and tighten them tighter.
• Replace motor reverser relay.
• Replace the washing machine motor.

Remember! For fulfillment recent two operations better apply to specialists.

F7 (are burning second, third and fourth indicators)

There are obvious problems with the electricity or the control unit.

Bug fix:

Measure the mains voltage. If it is normal (from 200 to 240 V), then the problem is in the control unit.

You need to check the condition of the module and replace it if necessary.

F8 (lit the first indicator)

Too much water has been poured into the washing machine tank. F8 error occurred due to problems with pressure switch, water inlet valve, cylinder tightness or control module.

Bug fix:

Check pressure switch and electrical circuits. Make sure the bottle is sealed. Test the governing model. In rare cases, error F8 occurs when the water pressure is too high and the inlet valve is open. Replace valve.

F9 (are burning the first and fourth indicators)

The problem is with the tachometer. Perhaps it was the tachogenerator or the engine that broke.

Problem fix:

Check contacts and wiring.

Check the engine tachometer and the engine itself. Replace part if necessary.

F10 (are burning the first and third indicators)

There is no information about locking the sunroof.Either the door is really badly closed or the washing machine is wrong about this.

F10 error fix:

Try to close the hatch more tightly and check if something else is interfering with this.

Check the electric lock and power circuits.

Make sure the sensor is working.

Check the electrical control module. Replace it if necessary.

door (are burning the first, third and fourth indicators)

The lock is broken. If the hatch is closed tightly and the electrical circuits are in order, then simply replace the lock.

F12 (are burning the first and second indicators)

The problem is in the motor drive. Check if the engine is running, if its stroke and power circuits are intact. A part may need to be replaced.

F13 (are burning the first, second and fourth indicators)

This mode is called other breakdowns. The system could not recognize the failure and highlighted the error F13. Check electrical circuits. They may be broken.

Important! For definitions Problems contact to specialists.

F14 (are burning the first and second indicators)

A software error has occurred. Here you definitely need to contact the workshop to identify the causes of the problem. In the worst case, you will have to change the electrical module.

F15 (in typewriters without display given error not provided, but may burn all four indicator)

A leak has occurred. Check it out. If found, inspect the cuffs of the hatch, the integrity of the tank and the drain system. Fix the leak yourself or contact a specialist.