Average characteristics of Electrolux washing machines Before we begin to analyze what caused the error with the E20 code, it is worth knowing what the Electrolux washing machine is. The average water consumption is 40 liters per wash. The capacity of the drum is 5 kilograms.
The spin speed is 1100 rpm. All these characteristics may vary depending on the model.
Electrolux machines are popular all over the world
They are reliable and easy to use. For the most part, the reviews about this unit are positive, this confirms the fact that the consumer trusts the Swedish manufacturer.
What does error E20 mean in the Electrolux washing machine
One of the most common errors in Electrolux washing machines is the E20 error. This malfunction occurs when there is a violation of the drain system for waste water. The damage may be in the drain hose, pump, drain filter, or electronics.
Most often, this problem can be solved independently, without resorting to the help of specialists.
Causes of a breakdown with code E20
Fault code E20 is usually displayed on the display of washing machines.This error tells the user of the washing machine that the machine cannot drain the waste water after washing. In this case, the machine may not drain water at all, or it may drain water, but at the same time, the signal that the drum is empty does not reach the electronic module boards.
The main reasons for incorrect operation of washing machines are blockages or kinks in the hose through which water is drained, blockages in the drain filter, blockage or damage to the pump, damage to the pump winding, and faulty contacts leading from the pump to the control module. With the worst outcome, the electronic module itself breaks down.
Repair methods
Before starting repair work, it is worth disconnecting the washing machine from the power supply and draining the water from the drum using the drain hose. When draining, you need to pay attention, if the water comes out without any problems, then the problem is either in the blockage of the sewer or in the pump. Then just pull the laundry out of the washing machine and you can start troubleshooting.
First, check the siphon into which the water is drained. If there are no blockages in it, then it is worth moving on to checking the drain pump and filter. After removing the filter, check it for blockages and, if any, get rid of them.
If the filter was clean, then proceed to the removal of the pump. In Electrolux washing machines, the pump is located near the back wall. You will need to remove the back cover of the washing machine and disconnect all the contacts from the pump. Then we climb under the bottom of the apparatus, there we unscrew the bolt on which the pump is held. Then remove the bandages from the drain hose and pull out the pump.
First check the pump for damage. If it is damaged, then it must be replaced.If outwardly it is intact, then it is worth checking it for blockages. To do this, unscrew the cover and check the impeller. Cleaning should be done with care so as not to damage the pump.
You will be lucky if the problems were related to the pump. After cleaning, install it back and run a test wash. If the drain works, then everything turned out well. However, in the absence of a drain, you need to continue diagnosing the washing machine.
At this stage, we should check the wires that lead from the pump to the control module. It is worth checking them for damage. If there is minor damage, then you must use electrical tape and rewind this wire. In case of major damage, the wire must be replaced.
At the very end, after a complete analysis of the hose, filter, pump and wires, we can conclude that the matter is in the control module. It will no longer be possible to deal with such a breakdown on your own, because for repair it is necessary to have the appropriate equipment and the scheme of the module boards. To fix this problem, you will need to change the burnt boards. This is a very difficult and responsible job.
Prevention of blockages and malfunctions
In order to avoid malfunctions in the operation of the washing machine, you must:
- Do not use hard water for washing to avoid scale.
- Use high quality washing powders.
- When loading things, make sure that no foreign objects get into the drum along with the things.
- From time to time check the condition of the hose, drain filter, pump and other components.
With proper operation, the washing machine can serve you for a long time without losing the quality of washing.
In conclusion, we can say that the E20 error is not as terrible as it might seem from the very beginning.Often this problem can be solved by yourself without any problems, but in rare cases it is necessary to resort to the help of a specialist, because only a master can fix your device.
