Average characteristics of the washing machine "Atlant". Before we figure out what causes the f4 error, it’s worth understanding what Atlant washing machines are. Devices of this brand have a relatively low price, without losing the quality of washing.
The average water consumption per wash is about 45 liters. Capacity about 5 kilograms. Small energy consumption. Management is automatic.
What does f4 error mean?
All specifications may vary by model. But we can confidently say that this is a high-quality washing machine.
Often, the f4 code occurs at the most inconvenient moment. On the display of the machine, right in the middle of washing, this alert appears. This means that the error has already occurred and needs to be fixed.
If your washing machine does not have a digital display, but has a self-diagnostic system, then you should pay attention to the lower set of bulbs. It is with the help of these LEDs that the device reports problems. If you have a digital display, then everything will be written on it.
In any display, the f4 error means the same problem. The problem is that there are problems with draining the waste liquid from the drum. Seeing this code, you need to urgently take measures to repair the washing machine.
Causes of breakdown
Before proceeding with the repair, it is worth finding out what exactly interferes with the discharge of dirty water.
The reasons can be both easy to eliminate, and some are worth tinkering with:
- The first reason could be the drain hose. The washing machine will not be able to get rid of the waste liquid if there is a blockage or the hose itself is bent somewhere. To deal with this problem, you just need to clean and straighten the hose.
- After checking the hose, the filter is checked, through which the drain is made. It is located on the front panel, behind the hatch. The filter must be clean and free of debris, dirt, sand, etc. The filter should be washed and cleaned.
-
The third in line is to check the impeller of the pump. We need to see if she can spin. If she is motionless, then it means that something is bothering her. To fix this problem, you will need to pull out and disassemble the pump according to the scheme. Clean it and make sure that the impeller is spinning.
- Also, having removed the pump, it is worth inspecting not only the impeller, but the entire pump as a whole. It is inspected for damage and blockages. You also need to check the integrity of its winding. If this is the problem, then the damage should be repaired and the winding replaced. However, if the damage is serious, then you will have to change the pump completely.
- The control unit is checked last. It is necessary to check the wiring loop leading from the pump directly to the board. With this problem, the wire is either insulated or must be replaced. At the very end, inspect the control board for faults.
Detailed troubleshooting guide
The reasons are now clear to us. Let's take a closer look at how to get rid of problems. It is worth starting with the simplest. It is necessary to disconnect the washing machine from the power supply and analyze the condition of the hose.Check if it has kinks. It is also worth checking it for blockages.
If the problem is not found, then move on. Find and clean the drain filter. Look for it in the lower right corner. After unscrewing and washing the filter, it is worth returning it to its original place. The simplest ends, if the washing machine still gives an error, then it is worth preparing the tools and going deeper.
To begin with, it is worth disconnecting the washing machine from the water supply and sewerage. Then get rid of the water from the tank. After all the manipulations, for convenience, turn the device on its left side. From the bottom you can see the pump. Disconnect all the wires from it, and then unscrew a few screws that hold the pump. After that, you can remove the pump from your washing machine.
Carefully inspect the pump for damage, if any, then the pump should be replaced. If there is a blockage or the winding is damaged, then the pump must be flushed and the winding replaced.
If the f4 code continues to be displayed, then the most difficult thing lies ahead. You will need to check the wires that go from the pump to the electronic module. They should be inspected at the time of damage. If such a wire is found, it is worth using it with electrical tape or replacing it.
Lastly, the electronic module itself is checked. Its breakdown is rare and it will be very difficult to repair the module on your own. If the problem is in it, then it will already be necessary to contact a specialist.
In conclusion, it is worth saying that if an f4 error appears, then you should not panic. Often, the washing machine can be repaired on its own, without resorting to the help of a specialist.Most often the problem is in the pump, you can easily replace it, but if the problem is in the electronics, it is better to contact a qualified technician.
